Home / Programming / StickyMat System – DWM

What can I do if I do not have enough cable?

StickyMat System – DWM

If you find that you do not have enough heating cable for your project, contact us and we’ll be happy to get more out to you! The cables can not be daisy chained.

Further Questions?

Troubleshooting

- Can the dual cable tester be used to measure the resistance of the floor sensor?

- What is a Dual Cable Tester and how do I use it?

- How do I reset the WiFi relay on a WSM snow melting controller?

- What if my thermostat screen is black and won’t turn on?

- Check the Resistance Readings of your Electric Floor Heating System

- Ground Fault Error: What does this Mean if my Thermostat has “Ground Fault Error” on the Display?

- Why is my Floor Temperature Reading Incorrect?

- Why hasn’t my Controller activated my snowmelt system if its snowing?

- What if the Sensor Probe Reads Higher or Lower than Actual Temperature?

- What does “ER1” on the thermostat display mean?

- Was your electric floor heating system installed directly on a concrete slab?

- Un-Mounting Your Thermostat

- Thermostat Reads Error Message “ER2” on the Display?

- Should I use Self-leveler or Thinset ?

- Output Fault Detected on the Display

- Once a repair has been completed, can I replace the tile right away?

- My Floor has No Heat but There Are No Error Messages?

- Is it Normal if I hear a Clicking Noise from my Thermostat?

- Heater Error: What Does it Mean if my Thermostat Reads “Heater Error” on the Display?

- Can I Cut the Electric Floor Heating System Wire if I Have too Much?

- Can I cut my floor heating mat if it’s too large?

- Are you getting a “Ground Fault” error after a few years?

- “ER1 Out” Thermostat Reading on the Display

- How to repair an electric floor heating cable system

- Floor Probe Installation Instructions

- What if my thermostat screen is black and won’t turn on?

- What are the electrical requirements for my Warmup system?

- I nicked the wire slightly; do I need a repair kit?

- Why is my thermostat flashing?

- Can I have a technician come to my home?

- How do I perform a GFCI Test on my thermostat?

- How does the infrared thermal camera work?

- Why does my thermostat say test monthly?

- What can I do if my old thermostat has stopped working?

- Why is my thermostat stuck on the Warmup screen?

- Is it possible to repair damaged underfloor heating?

- Can I delete a WSM in the application?

- What should I do if I change my WiFi settings at home and my WSM is not online anymore?

- How do I perform a factory reset on the WSM ?

- How do I connect my WSM-252W to WiFi?

- How do I test a floor probe?

- How do I test my heating cable(s)?

- What is the difference between a Watch Dog and an Alligator?

- ER1 on the Thermostat Meaning

- How to Check the Resistance Readings of your Electric Floor Heating System

- What Does the Control Fault Error Message Mean?

- What Does the Error Message on my Tempo Mean?

- How do I test my system using a Megger (Mega-Ohmmeter)?

- What does it mean if my thermostat reads “output fault detected” on the display?

- What is causing my thermostat to keep tripping requiring that I press the reset button?

- What does it mean if my thermostat reads “ER 1 Out” on the display?

- What if my thermostat says system is on however the floor is not heating up?

Installation

- What is a Dual Cable Tester and how do I use it?

- What is a Warmup Watchdog and how is it used?

- Can sheet vinyl be used on top electric under floor heat?

- What is the maximum thickness of tile over electric underfloor heating?

- Why does my floor heat unevenly?

- Why does my floor get warmer in some spots?

- Master/Relay (relay reading ER1)

- Installation Tips for the DWM Heating Mat System

- How to install a floor heating mat around a drain in a shower ?

- How far from the controller can the CIT-1 sensor be placed?

- How do turn on my thermostat unit?

- How do I check if the cable is working ?

- Can my sensor probe be extended?

- The Factory Joint Rule

- Installation of the CIT-1

- How do I install the factory joint which is thicker than the heater wire?

- Can Warmup Electric Heating be Installed in a Shower?

- Can I swap my 3iE to a 4iE or Tempo?

- Can I install my Warmup system directly on top of plywood?

- Can I install a 120V mat on one leg of a double pole breaker?

- Can I Have Another Thermostat as an Acting Relay?

- Can I connect one Warmup heater to another in series?

- Can I connect more than one Warmup heater to a thermostat?

- Can a wooden floating floor be installed directly over the Warmup NADWS system?

- What type of thinset should I use with my Warmup system?

- What do I need to prepare for my electric floor heating project?

- Do I choose cable or mat electric floor heating systems?

- Was your electric floor heating system installed directly on a concrete slab?

- Can I cut my floor heating mat if it’s too large?

- Specialized installation – under Nailed Hardwood

- Floor Probe Installation Instructions

- Floor Heating Loose Wire Installation Video

- Electric Floor Heating Mat Installation Video

- Will the Electric Floor Heating System Work Without the Floor Sensor Probe?

- Why does my heater have a ground wire but the thermostat has no terminal for ground?

- What are the electrical requirements for my Warmup system?

- If I have too much mat or cable, can I cut it?

- Can I upgrade to the 6iE?

- How far away from the wall should floor heat be installed?

- Can I cross floor heating cables?

- How long after flooring installation should we wait to use the heat?

- Can you install over tile?

- Can you trim the floor sensor?